This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
stmview [2010/07/22 09:54] prokop |
stmview [2010/07/23 13:43] prokop |
||
---|---|---|---|
Line 2: | Line 2: | ||
{{:stmview:stmview.tar.gz|}} | {{:stmview:stmview.tar.gz|}} | ||
+ | |||
+ | * The fork version which enable manual selection of minimum offset and scaling for rubbersheed. See the picture 4. This would enable to set | ||
+ | better positioning and roughness of the surface map in case when the default (automatic) positioning is not appropriate. Sometimes (if data in STM map has high values >1, the positioning of surface could be far from geometry) | ||
+ | {{:stmview:stmview-scale.tar.gz|}} | ||
==== Instalation ==== | ==== Instalation ==== | ||
Line 7: | Line 11: | ||
* Extract STMview folder and try to open MapAndBas-9.net in //OpenDX -> Data Explorer -> Run Visual Program//. I would not probably work correctly yet. | * Extract STMview folder and try to open MapAndBas-9.net in //OpenDX -> Data Explorer -> Run Visual Program//. I would not probably work correctly yet. | ||
* The "visual program" has hardwired absolute path to *.general files ( /home/prokop/Desktop/STMview ), you need to edit it. Look on the biggest "Control Panel" (see picture 1) and choose correct location of files "upravene-STM-out.genral" and "upravene-BAS.genral" in "Import name" dialog. Alternatively you can edit this dirrectly in text editor in MapAndBas-9.neb and MapAndBas-9.cfg | * The "visual program" has hardwired absolute path to *.general files ( /home/prokop/Desktop/STMview ), you need to edit it. Look on the biggest "Control Panel" (see picture 1) and choose correct location of files "upravene-STM-out.genral" and "upravene-BAS.genral" in "Import name" dialog. Alternatively you can edit this dirrectly in text editor in MapAndBas-9.neb and MapAndBas-9.cfg | ||
- | * Open "upravene-STM-out.genral" and "upravene-BAS.genral" in text editor and check if the first two lines matches the true location and size of files, if not edit it. Alternatively you can create correct new *.general files using //"OpenDX -> Data Explorer -> Import Data -> Grid or Scattered file"// : | + | * Open "upravene-STM-out.genral" and "upravene-BAS.genral" in text editor and check if the first two lines matches the true location and size of files, if not edit it. __Especially if there is relative address, change to absolute adress could help.__ Alternatively you can create correct new *.general files using //"OpenDX -> Data Explorer -> Import Data -> Grid or Scattered file"// |
<code> | <code> | ||
file = /home/prokop/Desktop/STMview/answer.bas | file = /home/prokop/Desktop/STMview/answer.bas | ||
Line 20: | Line 24: | ||
* Anytime you want to open a new file, you should edit the first two lines of "upravene-STM-out.genral" and "upravene-BAS.genral" as described above. | * Anytime you want to open a new file, you should edit the first two lines of "upravene-STM-out.genral" and "upravene-BAS.genral" as described above. | ||
* After that just Run the visual program MapAndBas-9.net and it should s view the geometry, surface and colorbar immediately. If not, there is probably a mistake in definitiion of paths. In this case try to checke Error message window and/or look on the imege window and run "Windows -> Open Visual Program Editor", there you can check what is wrong (shown yellow) | * After that just Run the visual program MapAndBas-9.net and it should s view the geometry, surface and colorbar immediately. If not, there is probably a mistake in definitiion of paths. In this case try to checke Error message window and/or look on the imege window and run "Windows -> Open Visual Program Editor", there you can check what is wrong (shown yellow) | ||
- | * If everythig goes well, check the "Control panle" | + | * If everythig goes well, check the "Control panel". There are several smaller controlpanels but the only importaint is the one shown on picture 1. Use picture 1 as a reference guide to this dialogs. |
+ | * To change the view go to //Options -> View Control//, There you want probably set "Mode:" to "Rotate" and/or "Set view" to "Front" | ||
=== Picture 1 - main Control Panel with help notes === | === Picture 1 - main Control Panel with help notes === |