dft_inputs
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
dft_inputs [2016/12/08 09:06] krejcio |
dft_inputs [2017/01/26 14:58] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Hartree potential that may serve as an input for the PPM can be produced by various DFT codes. The calculated system should be in the lower part of the unit cell, but z coordinates of the top-most layer has to be above zero! At least 10 Ǎ of vacuum above a slab geometry has to be used. 15-20 Ă of Vacuum are recommended. Here we show examples how to produce a hartree potential, for couple of DFT codes: | ||
| - | == Fireball == | ||
| - | |||
| - | A fireball.in for creation of an fftpot.xsf file with Hartree potential with using a McWEDA functional should look like: | ||
| - | |||
| - | &OPTION | ||
| - | basisfile = 'answer.bas' | ||
| - | lvsfile = 'input.lvs' | ||
| - | kptpreference = 'input.kpts' | ||
| - | nstepf = 1 | ||
| - | icluster = 0 | ||
| - | itdse = 0 | ||
| - | iqout = 1 | ||
| - | ifixcharge = 1 ! 0 if you don't have pre-calculated atomic charges in CHARGES | ||
| - | iquench = -1 | ||
| - | &END | ||
| - | | ||
| - | &OUTPUT | ||
| - | iwrtxsf = 1 ! print the important file | ||
| - | iwrtden = 1 ! print the important file | ||
| - | &END | ||
| - | | ||
| - | &MESH | ||
| - | ifixg0 = 1 ! | ||
| - | g0 = 0.0,0.0,0.0 ! do not shift the position of atoms in fftpot.xsf with respect to the answer.bas | ||
| - | Ecut = 300.0d0 ! not really necessary, but gives grid sampling approximately 100 pm. | ||
| - | &END | ||
| - | |||
| - | A fireball.in file for calculations with XC on a grid computations: | ||
| - | |||
| - | &OPTION | ||
| - | basisfile = 'answer.bas' | ||
| - | lvsfile = 'input.lvs' | ||
| - | kptpreference = 'samplek.kpts' | ||
| - | nstepf = 1 | ||
| - | icluster = 0 ! 0 for PBC / 1 for cluster calculation | ||
| - | itdse = 0 | ||
| - | iqout = 1 | ||
| - | ifixcharge = 0 | ||
| - | dt = 0.5 | ||
| - | iquench = -1 | ||
| - | iks = 1 | ||
| - | imcweda = 0 | ||
| - | idogs = 0 | ||
| - | bmix = 0.05 | ||
| - | &END | ||
| - | | ||
| - | &OUTPUT | ||
| - | iwrtxsf = 1 ! print the important file | ||
| - | iwrtden = 1 ! print the important file | ||
| - | &END | ||
| - | | ||
| - | &MESH | ||
| - | ifixg0 = 1 ! | ||
| - | g0 = 0.0,0.0,0.0 ! do not shift the position of atoms in fftpot.xsf with respect to the answer.bas | ||
| - | Ecut = 300.0d0 ! not really necessary, but gives grid sampling approximately 100 pm. | ||
| - | &END | ||
| - | |||
| - | == VASP == | ||
| - | |||
| - | [[http://www.vasp.at/]] | ||
| - | |||
| - | A LOCPOT file containing the Hartree potential is produced during standart VASP run. One just have to care about a dipole correction (if necessary). The LOCPOT file has to be convert into an *.xsf file, eg. via [[http://theory.chm.tu-dresden.de/~jk/software.html]] | ||
| - | |||
| - | == FHI-AIMS == | ||
dft_inputs.txt · Last modified: 2017/01/26 14:58 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
