stmview
Differences
This shows you the differences between two versions of the page.
|
stmview [2010/07/23 13:43] prokop |
stmview [2011/02/18 13:13] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ==== DOWNLOAD ==== | ||
| - | |||
| - | {{:stmview:stmview.tar.gz|}} | ||
| - | |||
| - | * The fork version which enable manual selection of minimum offset and scaling for rubbersheed. See the picture 4. This would enable to set | ||
| - | better positioning and roughness of the surface map in case when the default (automatic) positioning is not appropriate. Sometimes (if data in STM map has high values >1, the positioning of surface could be far from geometry) | ||
| - | {{:stmview:stmview-scale.tar.gz|}} | ||
| - | |||
| - | ==== Instalation ==== | ||
| - | * Correct instalation of OpenDX is expected (tested on SuSE 11.1) | ||
| - | * Extract STMview folder and try to open MapAndBas-9.net in //OpenDX -> Data Explorer -> Run Visual Program//. I would not probably work correctly yet. | ||
| - | * The "visual program" has hardwired absolute path to *.general files ( /home/prokop/Desktop/STMview ), you need to edit it. Look on the biggest "Control Panel" (see picture 1) and choose correct location of files "upravene-STM-out.genral" and "upravene-BAS.genral" in "Import name" dialog. Alternatively you can edit this dirrectly in text editor in MapAndBas-9.neb and MapAndBas-9.cfg | ||
| - | * Open "upravene-STM-out.genral" and "upravene-BAS.genral" in text editor and check if the first two lines matches the true location and size of files, if not edit it. __Especially if there is relative address, change to absolute adress could help.__ Alternatively you can create correct new *.general files using //"OpenDX -> Data Explorer -> Import Data -> Grid or Scattered file"// | ||
| - | <code> | ||
| - | file = /home/prokop/Desktop/STMview/answer.bas | ||
| - | points = 250 | ||
| - | </code> | ||
| - | <code> | ||
| - | file = ./empty05.out | ||
| - | grid = 25 x 25 | ||
| - | </code> | ||
| - | | ||
| - | ==== Usage ==== | ||
| - | * Anytime you want to open a new file, you should edit the first two lines of "upravene-STM-out.genral" and "upravene-BAS.genral" as described above. | ||
| - | * After that just Run the visual program MapAndBas-9.net and it should s view the geometry, surface and colorbar immediately. If not, there is probably a mistake in definitiion of paths. In this case try to checke Error message window and/or look on the imege window and run "Windows -> Open Visual Program Editor", there you can check what is wrong (shown yellow) | ||
| - | * If everythig goes well, check the "Control panel". There are several smaller controlpanels but the only importaint is the one shown on picture 1. Use picture 1 as a reference guide to this dialogs. | ||
| - | * To change the view go to //Options -> View Control//, There you want probably set "Mode:" to "Rotate" and/or "Set view" to "Front" | ||
| - | |||
| - | === Picture 1 - main Control Panel with help notes === | ||
| - | |||
| - | {{:stmview:contropanael--.png|Picture 1 - main Control Panel with help notes}} | ||
| - | |||
| - | === Picture 2 - 3D view with hi opacity (0.9) === | ||
| - | |||
| - | {{:stmview:screenshot2.png|Picture 2 - 3D view with hi opacity (0.9)}} | ||
| - | |||
| - | === Picture 3 - View from front (go to " Options -> View Control -> Set View -> Front ") with hi opacity (0.5) === | ||
| - | |||
| - | {{:stmview:screenshot-1.png| Picture 3 - View from front (go to " Options -> View Control -> Set View -> Front ") with hi opacity (0.5)}} | ||
| - | |||
stmview.txt ยท Last modified: 2011/02/18 13:13 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
